Gel coat is the outer layer of fiberglass. Its structural value is not significant. However, it gives the product its shine and color. In addition, it offers protection to the hull. Read on to know more on how to restore faded fiberglass.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If there is mildew, you will have to add some bleach. Sometimes, stains are difficult to eliminate. You will have to apply a concentrated cleaner directly to the spot. Do not forget to rinse the surface thoroughly after the cleaning process. You can use a clean cotton cloth to dry the product or let it dry naturally.
For better results, all oil should be removed from the item. Not all detergents succeed in accomplishing this. Acetone or MEK should be used for this purpose. However, it is advisable to use a microfiber cloth to apply it. Direct application is discouraged. You may need several of them because you have to discard it once they are covered up with grease. The next step is to wax the item. This can prolong its life.
You will have to follow the instructions of your manufacturer carefully. Remember that not all waxes have the same procedure of application. However, you will need a cloth in waxing. Circular motions are encouraged. Wait until the wax is dry to buff the extra. You need a special cloth for this task.
The next step is polishing. This should be done using an abrasive. Fine sandpaper is preferred. It will remove pitted areas. This is not something you can achieve with coating. You should tackle a small section at a time. In addition, the motions have to be circular. Go on until you can see your reflection on the surface. An extra layer of wax should be added after you are done polishing for protection. Some preparations contain wax in the formulation.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer should be applied last. There are a lot of them meaning you will not have a difficult time shopping for one. They work almost the same as wax. Nonetheless, buffing is recommended after the restorer has being applied. You will be impressed with the results. However, remember that the item will not retain the new look forever. However, it will last for some time if you take care of it well.
Because the product is exposed to various conditions over time, erosion of its outer layer is normal. This will leave it looking ugly. However, there is a way to fix this. Before you do anything else, you should ensure the surface is clean. You will need water, a sponge and detergent for this. It is better if the water is warm. Remember to protect your hands before starting the cleaning.
If there is mildew, you will have to add some bleach. Sometimes, stains are difficult to eliminate. You will have to apply a concentrated cleaner directly to the spot. Do not forget to rinse the surface thoroughly after the cleaning process. You can use a clean cotton cloth to dry the product or let it dry naturally.
For better results, all oil should be removed from the item. Not all detergents succeed in accomplishing this. Acetone or MEK should be used for this purpose. However, it is advisable to use a microfiber cloth to apply it. Direct application is discouraged. You may need several of them because you have to discard it once they are covered up with grease. The next step is to wax the item. This can prolong its life.
You will have to follow the instructions of your manufacturer carefully. Remember that not all waxes have the same procedure of application. However, you will need a cloth in waxing. Circular motions are encouraged. Wait until the wax is dry to buff the extra. You need a special cloth for this task.
The next step is polishing. This should be done using an abrasive. Fine sandpaper is preferred. It will remove pitted areas. This is not something you can achieve with coating. You should tackle a small section at a time. In addition, the motions have to be circular. Go on until you can see your reflection on the surface. An extra layer of wax should be added after you are done polishing for protection. Some preparations contain wax in the formulation.
Sometimes the product is worn significantly. In such a case, even polishing will not give back its shine. You will have to use a very strong abrasive during the scrubbing. You should remove any remaining wax on the surface before you begin polishing it. It can make the compound appear uneven. While clearing the wax, do not move up and down but rather on a straight line. Toluene or a de-waxing solution should be utilized.
A restorer should be applied last. There are a lot of them meaning you will not have a difficult time shopping for one. They work almost the same as wax. Nonetheless, buffing is recommended after the restorer has being applied. You will be impressed with the results. However, remember that the item will not retain the new look forever. However, it will last for some time if you take care of it well.
About the Author:
When you are looking for information about how to restore faded fiberglass, pay a visit to our web pages online here today. Additional details are available at http://www.leprechaunmagic.com now.
